-
| .
|
Utente Race
- Group
- Administrator
- Posts
- 620
- Reputation
- +73
- Location
- Monzuno (BO)
- Status
- Offline
|
|
Visto il lockdown sto facendo un po' di lavori e nello smontare tutta la parte dietro, ho notato il suppporto del motore rotto.. effettivamente i due bulloncini di 6mm che tengono su il motore era ovvio che si rompessero in quel punto..
così gli ho saldato sopra altra spiaggia di ferro da 2mm e rifatti i fori, saldandola in tutto il perimetro, speriamo che tenga..Attached Image
|
|
| .
|
-
| .
|
Utente Race
- Group
- Administrator
- Posts
- 620
- Reputation
- +73
- Location
- Monzuno (BO)
- Status
- Offline
|
|
ecco il rinforzo saldato Attached Image
|
|
| .
|
-
| .
|
Utente Race
- Group
- Member
- Posts
- 436
- Reputation
- +20
- Location
- Prague
- Status
- Offline
|
|
Good job! now I am concerned and I need to check mine now if all ok...
D8
|
|
| .
|
-
| .
|
Utente Race
- Group
- Administrator
- Posts
- 620
- Reputation
- +73
- Location
- Monzuno (BO)
- Status
- Offline
|
|
praticamente tutto il peso motore è attaccato su quella piccola flangia, quindi rompendosi quella tutto il peso grava sul motoriduttore e sui 3 sillentblock del telaietto del riduttore, infatti uno dei 3 è totalmente rotto Attached Image
|
|
| .
|
-
| .
|
Utente a 6V
- Group
- Member
- Posts
- 48
- Reputation
- +11
- Location
- belgium
- Status
- Offline
|
|
I've not this problem with my modele 2009 but retrofited in 2013, maybe because the "silent kit" , much many vibration and more absortion of shock.
No photo but info pdf
Do you've silent kit?File Allegato
|
|
| .
|
-
| .
|
Utente Race
- Group
- Administrator
- Posts
- 620
- Reputation
- +73
- Location
- Monzuno (BO)
- Status
- Offline
|
|
CITAZIONE (tazzafred @ 24/11/2020, 19:28) Do you've silent kit? yes, mine is a 2012 SE and i have all those silent block mounted
|
|
| .
|
-
| .
|
Utente Economy
- Group
- Member
- Posts
- 107
- Reputation
- +9
- Location
- Bucarest, Romania
- Status
- Offline
|
|
It looks like this is a common failure mode: just found the flange broken in the same place on my (ex. DarkRider's) classic Zerro. The silent kit is present even though it is at least partially incorrectly mounted. The 3 small silent blocks are dead and the opposing top mount is no longer in compression due to the broken flange.
The question here is: Do you guys have dimensions for all these silent blocks I will need to replace? I can of course measure them myself but i was hoping to have an early start and order the parts before I have the chance to take everything out and measure myself ...Attached Image
|
|
| .
|
-
| .
|
Utente Economy
- Group
- Member
- Posts
- 107
- Reputation
- +9
- Location
- Bucarest, Romania
- Status
- Offline
|
|
QUOTE (zeAndrea @ 11/23/2020, 12:54 PM) praticamente tutto il peso motore è attaccato su quella piccola flangia, quindi rompendosi quella tutto il peso grava sul motoriduttore e sui 3 sillentblock del telaietto del riduttore, infatti uno dei 3 è totalmente rotto Same block completely broken in my case too:Attached Image
|
|
| .
|
-
| .
|
Utente a 6V
- Group
- Member
- Posts
- 55
- Reputation
- +10
- Status
- Offline
|
|
QUOTE (charliefdt @ 19/9/2022, 08:23) The question here is: Do you guys have dimensions for all these silent blocks I will need to replace? I can of course measure them myself but i was hoping to have an early start and order the parts before I have the chance to take everything out and measure myself ... These are the dimensions of our old ones: Inner diameter: 12mm with width 30mm, outer diameter: 40mm with width: 25mm. (The central part is wider). We couldn´t find any online with the right measurements so we bought these: from auto-doc.it They are a bit stronger and a bit wider, so we had to use longer screws on the lateral two and had to trim the sides of the central one.Attached Image
|
|
| .
|
-
| .
|
Utente Economy
- Group
- Member
- Posts
- 107
- Reputation
- +9
- Location
- Bucarest, Romania
- Status
- Offline
|
|
QUOTE (Bi_Gia @ 9/19/2022, 11:19 AM) These are the dimensions of our old ones: Inner diameter: 12mm with width 30mm, outer diameter: 40mm with width: 25mm. (The central part is wider). We couldn´t find any online with the right measurements so we bought these: from auto-doc.itThey are a bit stronger and a bit wider, so we had to use longer screws on the lateral two and had to trim the sides of the central one. Thank you for the measurements and part sugestion! I bought the same and trimmed all of them down:
|
|
| .
|
-
| .
|
Utente Economy
- Group
- Member
- Posts
- 107
- Reputation
- +9
- Location
- Bucarest, Romania
- Status
- Offline
|
|
| .
|
-
| .
|
Utente a 6V
- Group
- Member
- Posts
- 57
- Reputation
- +5
- Status
- Offline
|
|
I did this on the single motor mount on top of the engine ,didnt have time to wait for the part . Drill 2 new wholes a few cm longer down on the broken off part . Take off the bracket on top of the rubber and turn it up side down . You have to bend out little bit in the bracket and carefully grind litle bit rubber to make the bracket fit up side down …bush fix
|
|
| .
|
11 replies since 23/11/2020, 10:23 327 views
.